APLIKASI LIMBAH KERTAS UNTUK PEMBUATAN BATAKO
DOI:
https://doi.org/10.29103/jtku.v13i1.19560Keywords:
Limbah kertas, Batako, Kuat TekanAbstract
Aktivitas sehari-hari yang terjadi di lingkungan Fakultas Teknik Universitas Halu Oleo tidak terlepas dari sampah kertas, khususnya sampah kertas HVS. Penelitian ini bertujuan untuk mengetahui komposisi optimum batako dengan penambahan limbah kertas dan mengetahui kualitas produk batako dengan penambahan limbah kertas. Metode penelitian ini menggunakan metode eksperimen dengan perbandingan PC : PS = 1 : 6 yang kemudian diubah menjadi perbandingan volume. Variasi penambahan limbah kertas adalah 5%, 15%, dan 25% dari volume pasir yang dibutuhkan. Penelitian ini mengacu pada SNI 03-0349-1989. Hasil uji kuat tekan pada umur 28 hari, nilai uji kuat tekan tertinggi pada variasi 5% dengan kuat tekan sebesar 56,67 Kg/cm2. Nilai kuat tekan terendah terjadi pada variasi 25% dan kuat tekan sebesar 33,60 Kg/cm2. Sedangkan kuat tekan batako normal yang ada di pasaran lebih rendah dibandingkan dengan kuat tekan batako yang diberi tambahan kertas. Kuat tekan batako normal 1 = 41,31 Kg/cm2, batako normal 2 = 16,67 Kg/cm2, dan batako normal 3 = 2,85 Kg/cm2. Hal ini menunjukkan bahwa variasi batako dengan penambahan limbah kertas 5%, 15% dan 25% lebih unggul dibandingkan batako normal yang ada di pasaran yang mampu memenuhi standar mutu SNI batako yaitu mutu kelas III dan IV.
References
Abbas, S., Saleem, M. A., Kazmi, S. M., & Munir, M. J. (2017). Production of sustainable clay bricks using waste fly ash: Mechanical and durability properties. Journal of Building Engineering, 14, 7-14.
Abdel-Shafy, H. I., & Mansour, M. S. (2018). Solid waste issue: Sources, composition, disposal, recycling, and valorization. Egyptian journal of petroleum, 27(4), 1275-1290.
Alamsyah, M. I., Sriyani, R., & Rachman, R. M. (2020). Pengujian Pemanfaatan Limbah Gelas Plastik Polypropylene (PP) Dalam Komposisi Campuran Beton.
Chen, F., Wu, K., Ren, L., Xu, J., & Zheng, H. (2019). Internal curing effect and compressive strength calculation of recycled clay brick aggregate concrete. Materials, 12(11), 1815.
Adams, H. (2015). Adams' Building Construction. Routledge..
Aneke, F. I., Awuzie, B. O., Mostafa, M. M., & Okorafor, C. (2021). Durability assessment and microstructure of high-strength performance bricks produced from pet waste and foundry sand. Materials, 14(19), 5635
Badan Standarisasi Nasional. (1989). SNI 03-0349-1989 Spesifikasi Bata beton untuk pasangan dinding. Sni 03-0349-1989, 1, 1-6
Bellei, P., Arromba, J., Flores-Colen, I., Veiga, R., & Torres, I. (2021). Influence of brick and concrete substrates on the performance of renders using in-situ testing techniques. Journal of Building Engineering, 43, 102871.
de Azevedo, A. R., Alexandre, J., Pessanha, L. S. P., da ST Manhães, R., de Brito, J., & Marvila, M. T. (2019). Characterizing the paper industry sludge for environmentally-safe disposal. Waste Management, 95, 43-52.
Hospodarova, V., Stevulova, N., Briancin, J., & Kostelanska, K. (2018). Investigation of waste paper cellulosic fibers utilization into cement based building materials. Buildings, 8(3), 43
Irna Hendriyani, Rahmat, S. M. D. (2017). Research of Manufacture Brickworks With Hvs Waste. Snitt Poltekba, 316-321.
Jamal, M., Ahmad, S. N., Ampangallo, B. A., Serang, R., & Rachman, R. M. (2024). Beton Pracetak (Teknologi, Produksi dan Aplikasi). TOHAR MEDIA.
Jumiati, E. (2021). Karakteristik Sifat Fisis Batako Berbahan Limbah Kertas. Jurnal Ikatan Alumni Fisika, 7(3), 7. https://doi.org/10.24114/jiaf.v7i3.27618
Kesuma, A. (2022). Analisa Pengaruh Penambahan Limbah Kertas Sebagai Substitusi Parsial Semen Dengan Bahan Tambah Epoxy Resin Terhadap Kuat Tekan Beton. Jurnal Teknik Sipil, 106, 1-12.
Muñoz, P., Letelier, V., Muñoz, L., & Bustamante, M. A. (2020). Adobe bricks reinforced with paper & pulp wastes improving thermal and mechanical properties. Construction and Building Materials, 254. https://doi.org/10.1016/j.conbuildmat.2020.119314
Murmu, A. L., & Patel, A. (2018). Towards sustainable bricks production: An overview. Construction and building materials, 165, 112-125.
Rachman, R., Syaban, A. R., & Setiawan, T. A. (2020). Faktor-Faktor yang Berhubungan dengan Pengelolaan Sampah Rumah Tangga di Kelurahan Sanua Kota Kendari Tahun 2018. Jurnal Ilmiah Teknik Sipil, 8(1), 37-49
Rachman, R. M., Bahri, A. S., & Trihadiningrum, Y. (2018). Stabilization and solidification of tailings from a traditional gold mine using Portland cement. Environmental Engineering Research, 23(2), 189-194.
Rangan, P. R. (2018). Pengaruh Pemanfaatan Limbah Kertas HVS Sebagai Bahan Tambah Batako Pejal Terhadap Kuat Tekan. Journal Dynamic Saint, 3(2), 684-710. https://doi.org/10.47178/dynamicsaint.v3i2.430
Sofi, M., Sabri, Y., Zhou, Z., & Mendis, P. (2019). Transforming municipal solid waste into construction materials. Sustainability, 11(9), 2661.
Terrones-Saeta, J. M., Suárez-MacÃas, J., Corpas-Iglesias, F. A., Korobiichuk, V., & Shamrai, V. (2020). Development of ceramic materials for the manufacture of bricks with stone cutting sludge from granite. Minerals, 10(7), 621.
Torrent, R. J., Neves, R. D., & Imamoto, K. I. (2021). Concrete permeability and durability performance: from theory to field applications. CRC Press
Downloads
Additional Files
Published
Issue
Section
License
Authors retain copyright and grant the journal right of first publication and this work is licensed under a Creative Commons Attribution-ShareAlike 4.0 that allows others to share the work with an acknowledgement of the works authorship and initial publication in this journal.
All articles in this journal may be disseminated by listing valid sources and the title of the article should not be omitted. The content of the article is liable to the author.
Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.
In the dissemination of articles by the author must declare the Jurnal Teknologi Kimia Unimal as the first party to publish the article.
