ANALISA PENGARUH HOLDING TIME DAN TEMPERATUR PADA PACK CARBURIZING MENGGUNAKAN LIMBAH KULIT SINGKONG TERHADAP SIFAT FISIK DAN MEKANIK BAJA 1020

Ali Fikri, Muhammad Muhammad, Abdul Rahman, Reza Putra, Muhammad Habibi

Abstract


The purpose of this study to determine the effect holding time on increasing the surface hardness of AISI 1020 steel material and analyzing the physical and mechanical properties of the results pack carburizing cassava peel waste on AISI 1020 steel. Process pack carburizing in this study have variations temperature 875oC and 900oC withholding time 60 minutes, 80 minutes, 100 minutes and 120 minutes. The catalyst used in this study was a carbonate compound, namely 20% BaCo3 to accelerate the reaction of adding carbon. The research results show that pack carburizing from cassava peel waste carbon can increase the surface hardness of AISI 1020 steel or part of the mechanical properties of the material. Testing at a temperature of 875oC withholding time 60 minutes which is 10.7 HRC and is the lowest value in the study while the highest hardness value occurs at a temperature of 900OC withholding time 120 minutes is 48.2 HRC. Microstructure observation results (metallography) on the edges indicates the martensite phase. The more martensite phase, the higher the value of the surface hardness of the steel material in the same direction as the effect of the length of holding time(holding time)

Full Text:

PDF

References


Kementan, R. (2018). Produksi Ubi Kayu1) Menurut Provinsi, 2014 - 2018. Data Produksi Ubi Kayu. https://www.fairportlibrary.org/images/files/RenovationProject/Concept_cost_estimate_accepted_031914.pdf

Maulinda, L., Nasrul, Z., & Sari, D. N. (2015). Jurnal Teknologi Kimia Unimal Pemanfaatan Kulit Singkong sebagai Bahan Baku Karbon Aktif. Jurnal Teknologi Kimia Unimal, 4(2), 11–19.

Muslih, & Nasution, R. H. (2020). Analisa Kekerasan Dan Struktur Mikro Baja Aisi 1020 Terhadap Perlakuan Carburizing Dengan Arang Batok Kelapa. Buletin Utama Teknik, 15(2), 165–173.

Muhammad, M., Reza Putra, T. Hafli, Nurul Islami, and Abdul Malik. "Pengaruh Fraksi Volume Serat Terhadap Kekuatan Tarik Komposit Serat Daun Nanas dan Sabut Kelapa dengan Polyester Bening 108." Malikussaleh Journal of Mechanical Science and Technology 7, no. 1 (2023): 68-73.

Ngakan, D., Putra, K., Made, I. D., & Muku, K. (n.d.). Pack carburizing Baja Karbon Rendah. 167–172.

Putra, Reza, Muhammad Muhammad, T. Hafli, Nurul Islami, and Muhammad Nugraha. "Analysis of the Mechanical Properties of Teak Sawdust-Reinforced Composite Boards Affected by the Alkalization Process." International Journal of Engineering, Science and Information Technology 2, no. 4 (2022): 11-18.

Suprianto, dedi. (2015). Pengaruh Variasi Temperatur Pada Proses Hardening Terhadap Kekerasan, Struktur Micro Baja Aisi 1025 Dengan Media Pendingin. Paper Knowledge . Toward a Media History of Documents, 3(April), 49–58.

Wisnujati, A., Vokasi, P., & Yogyakarta, U. M. (2017). Analisis perlakuan. 8(1), 127–134.




DOI: https://doi.org/10.29103/mjmst.v7i2.13647

Article Metrics

 Abstract Views : 211 times
 PDF Downloaded : 41 times

Refbacks

  • There are currently no refbacks.


Copyright (c) 2023 Muhammad Muhammad

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.